Skip to content
Onlitex

A glossary of 26 terms used every day in PCB fabrication and PCBA processing, from annular ring and thieving to V-score, solder pot and wave soldering.

Onlitex Engineering Team4 min read
Rack of assembled printed circuit boards

Here are 26 professional terms commonly used in the PCBA processing industry, grouped by where you are most likely to meet them.

Board design and fabrication terms

  • Annular ring: The copper ring around a plated through-hole in a PCB.
  • DRC (design rule check): A software check of the design to make sure it contains no errors, such as traces that touch incorrectly, traces that are too thin or drill holes that are too small.
  • Drill hit: The locations in the design where holes should be drilled, or where they are actually drilled on the board. Inaccurate drill hits caused by blunt drill bits are a common manufacturing problem.
  • Gold finger: Exposed metal pads along the edge of a circuit board, used to make a connection between two circuit boards. Common examples are the edges of computer expansion cards and memory modules, and older cartridge-based video games.
  • Pad: The exposed metal on the surface of a circuit board that components are soldered to.
  • Plane (copper pour): A continuous block of copper on a circuit board, defined by a boundary rather than a path. It is also commonly called a "pour".
  • Plated through-hole (PTH): A hole in a circuit board that has an annular ring and is plated all the way through the board. It may be a connection point for a through-hole component, a via that carries a signal, or a mounting hole. For example, when a PTH resistor is inserted into a PCB ready for soldering, its legs pass through the holes. Plated holes can have traces connected on both the front and back of the PCB.
  • Silkscreen: The letters, numbers, symbols and images on a circuit board. Usually only one color is available, and the resolution is usually quite low.
  • Slot: Any non-circular hole in the board, which may or may not be plated. Slots sometimes increase the cost of the board because they require extra cutting time. Note that the corners of a slot cannot be made completely square, because they are cut with a round milling cutter.
  • Solder mask: A layer of protective material over the metal that prevents short circuits, corrosion and other problems. It is usually green, but other colors (SparkFun red, Arduino blue or Apple black) are also possible. It is sometimes called "resist".
  • Thermal relief: A small trace used to connect a pad to a plane. Without thermal relief, it is difficult to get the pad hot enough to form a good solder joint. When you try to solder a pad without proper thermal relief, it feels "sticky" and reflow takes an unusually long time.
  • Thieving: Hatched lines, grid lines or copper dots left in areas of the board that have no plane or traces. Thieving makes etching easier, because less time is needed to remove unwanted copper in the etching bath.
  • Trace: A continuous path of copper on a circuit board.
  • Via: A hole in a circuit board used to pass a signal from one layer to another. Tented vias are covered with solder mask to prevent them from being soldered. Vias used to connect connectors and components are usually left uncovered so they can be soldered easily.

Panelization terms

  • Panel: A larger circuit board made up of many smaller boards, which are separated before use. Automated board processing equipment often has trouble handling smaller boards, so grouping several boards together can significantly speed up processing.
  • Stamp holes (mouse bites): An alternative to V-scoring for separating boards from a panel. Many drill holes are grouped closely together to form a weak line, so the board can easily be broken off afterwards.
  • V-score: A partial cut through the board that allows it to be snapped easily along a line.

Assembly and soldering terms

  • Paste stencil: A thin metal (sometimes plastic) template placed over the circuit board that allows solder paste to be deposited in specific areas during assembly.
  • Pick and place: The machine or process that places components on a circuit board.
  • Spring contact (pogo pin): A spring-loaded contact used to make a temporary connection for testing or programming.
  • Reflow soldering: Melting solder to form a joint between a pad and a component lead.
  • Solder paste: Small solder balls suspended in a gel medium, applied to the surface-mount pads of a PCB with the help of a paste stencil before components are placed. During reflow soldering, the solder in the paste melts, forming electrical and mechanical joints between the pads and the components.
  • Solder pot: A pot used for quickly soldering boards with through-hole components by hand. It usually contains a small amount of molten solder; the board is dipped into it quickly, leaving solder joints on all the exposed pads.
  • Solder jumper: A small blob of solder connecting two adjacent pins of a component on a circuit board. By design, solder jumpers can be used to connect two pads or pins together, but they can also cause unwanted short circuits.
  • Surface mount: A construction method that allows components to be mounted directly on the board, without leads passing through holes in the board. It is the main assembly method used today, and it allows circuit boards to be assembled quickly and easily.
  • Wave soldering: A soldering method for boards with through-hole components, in which the board passes over a standing wave of molten solder that adheres to the exposed pads and component leads.
  • #PCBA glossary
  • #PCB terms
  • #PCB assembly
Share:

Keep reading

Guides· 1 min

What Is PCBA? PCB vs PCBA Explained

What a printed circuit board (PCB) is, what a printed circuit board assembly (PCBA) is, and the key difference between a bare PCB and a finished PCBA.

Send your Gerber files and BOM. Quotation within 48 hours, no minimum order.